How To Program Your Garage Door Operator Remote Control or Outside Keypad Below is information to help you program your Garage Door Operator remote control or outside keypad. If you need additional help, feel free to give a call for assistance or to schedule a service call to program for you. CHAMBERLAIN / LIFTMASTER / SEARS CRAFTSMAN GARAGE DOOR OPENERS Programming 971LM and 973LM, 371LM and 373LM Security Plus Transmitters. Press and release the “smart” button on garage door opener motor unit. The smart indicator light will glow steadily for 30 seconds. The 971LM and 973LM remotes have a corresponding amber or red, square, learn button. The 371LM and 373LM have a corresponding purple, square, learn button.
Learn buttons are located on the motor head near the terminal strip for wire connections. Within 30 seconds, press and hold the button on the hand-held remote. Release the button when the motor unit light blinks. It has learned the code. If light bulbs are not installed, two clicks will be heard.
LIFTMASTER AND SEARS CRAFTSMAN WIRELESS KEYPADS 976LM, 377LM Security Plus and 66LM Wireless Keyless Entry Systems. Press and release the “smart” button on garage door opener motor unit. The smart indicator light will glow steadily for 30 seconds. Within 30 seconds, enter a four digit personal identification number (PIN) of your choice on the keypad.
Then press and hold the ENTER button. Release the button when the garage door opener motor unit lights blink. It has learned the code. If light bulbs are not installed, two clicks will be heard. The square smart button is located on the side or the back of the motor head, and is colored red, green, amber, orange, or purple. It is directly under the #1 wire terminal screw. Programming Instructions for Genie Remotes: Programming Genie Intellicode Remote Transmitters.
Press the Receiver Learn Code button on the power head receiver of your door operator. This small, black, unmarked button is located behind the light lens at the motor head and is nearest the floppy 6 inch antenna wire that protrudes from the motor head. When pressed, a radio signal indicator light will start blinking red for 30 seconds. After pressing the Learn Code Button once, press your transmitter button three times for your system to grab the frequency and code it in.
(Keep the transmitter you want tuned at least 2 feet away from the power head while tuning.). Press the transmitter button once more to test the system and start your door moving. To erase all Intellicode remotes and wireless keyless entry, hold down on the learn button until the indicator light stops blinking, then proceed to Step 2. Programming Genie Digital Remote Transmitters with Internal Set Switches These transmitters work by matching the settings on the internal code setting switches with the same set of switches in the receiver on the garage ceiling. The receiver is located either behind the light lens of the Genie garage door opener motor head, or inside an external small rectangular box on the ceiling, which is connected to the motor head by a set of wires. Note: the frequency of the transmitter must be the same frequency as the receiver on the ceiling for it to work.
Genie has been making the 390 MHz frequency exclusively for the last 15 years. Programming Genie Multi-Button Digital Remotes with Internal Set Switches These garage door opener transmitters have 2 smaller switches to the right of the internal Code Setting Switches. The small right switch should be set according to how many Code Setting Switches in your receiver (either 9 or 12). The small left switch is for programming purposes.
To program a button for one of your doors, follow the instructions below:. First, match the settings on the Internal Code Setting Switches with the same set of switches in the receiver on the garage ceiling, as described in the previous programming instructions. Next, move the small programming switch to ‘S’ (for SET) and press the transmitter button you wish to have assigned to the above door. Last, return the programming switch to ‘R’ (for RUN) and press the assigned transmitter button to test the door and start the door moving. Follow the same procedure for each additional door you wish to program. Genie Garage Door Opener Keypads Genie Garage Door Opener Wireless Keypad Model GPWK-12, GWK (works with remotes having 9 or 12 internal code setting switches. Keypad is black with a slide-up cover showing the Genie logo only) Step-By-Step Programming Procedure.
Reset Keypad–slide keypad cover half way up. While pressing the # and 8 buttons simultaneously, slide the Keypad Cover the rest of the way up until it latches. Release # and 8 buttons. At this point, if the back lit keypad light stays on, proceed directly to step 2. If the back lit keypad light goes out, close the cover pad and reopen it until it clicks. Proceed to step 2. Press 3, 5, 7 and # buttons in said order.
Enter your PIN and press the # button. Your PIN number can be created from any group of numbers up to 8 digits of your choice. Note: Do NOT use”#” or “star” key. Enter Door Code, as determined from the chart at left, and press the “star” key. Slide Keypad Cover down. Test Keypad by sliding cover up until it latches.
Enter your PIN and Press “star” key. Your door should operate. This keyless garage door opener entry pad works with Genie transmitters using 390 MHz frequency. It is NOT compatible with Genie Intellicode transmitters (if your keypad has Intellicode printed on the cover, go to the next set of programming instructions below). The Door Code in the Step-By-Step Procedure at right is determined by the internal code switches inside your transmitter and the accompanying chart. Determine the settings of the first 3 switches and write down the corresponding number from the chart. Continue with the next 3 switches and its corresponding number, and so on, until the last set of 3 switches.
You should have 3 or 4 Door Code numbers. Switch Settings Door Code Number Up Up Up 7 Up Up Down 6 Up Down Up 5 Up Down Down 4 Down Up Up 3 Down Up Down 2 Down Down Up 1 Down Down Down 0 Door Code in Step #4: Genie Wireless Intellicode Keyless Entry Pad Programming 2 Models Model 1: Intellicode Model GWKIC, ACSDG (black with slide-up cover and the word “Intellicode” printed on the cover) GWKIC, ACSDG, Two Part, Step-By-Step Programming Part 1: To Reset the Intellicode Wireless Keypad.
Dec 30, 2017 - 100 Percent Love Video Songs Hd 1080p Telugu > Voir.100.Percent.Love.||.Telugu.Full.Movie.||.Naga.Chaitanya. 100 percent love telugu movie in hd. Jun 14, 2011 - 100% Love - Telugu Move torrent free download. Download Link: http://downloads.ziddu.com/downloadfile/15003672/100Love.rar.html. Telugu Movies Online HD DVD: Orange Telugu Movie Online - Ram Charan Teja, Genelia D'Souza S, hazahn Padamsee and Sanchita Shetty. Nov 23, 2012 - IMDB: Screen Shots: 100% love (2011) Telugu 100%లవ్. View Online On Youtube.
Open cover half way. Press and hold “PROG” and “8” while fully opening cover. Indicator light will blink once and go out. Close cover fully. To Program the Intellicode Wireless Keypad. Open cover fully by sliding keypad cover up until it latches.
Press 3-5-7. Press “PROG”.
(red light blinks). Enter your Personal Identification Number (PIN). Gran turismo 4 ntsc iso games. Press “PROG”.
(red light blinks fast). Close cover fully. Proceed to Part 2 above. NOTE: If red indicator light does not blink, it is not taking the programming steps. Check the 9 volt battery under the keypad numbers. To access, press inward, under the number pad lip while sliding downward to expose the battery.
Part 2: Press the Receiver Learn Code button on the Power Head Receiver of your Genie Garage Door Opener. This small black button is located behind the light lens at the motor head and is nearest the floppy 6 inch antenna wire that protrudes from the power head.
When pressed, a radio signal indicator will start blinking red for 30 seconds. Enter your PIN number after pressing the Learn Code button described above, while the motor head indicator light is blinking. Press “SEND” 2 times for your system to grab your frequency and code it in. Press “SEND” once to test system and start your door moving. Adding More Doors to Keypad:. Open cover fully. Enter PIN 1.
Press PROG, PROG, PROG. Enter total number of doors (2 or 3). Press PROG. Follow directions below to set each door. Press operator Learn Code Button.
Enter PIN 1. Press SEND. Enter Door Number (1, 2 or 3).
Press SEND three times. Close Cover. Test by Opening Cover, Enter PIN1, Enter 1. Go to next machine and follow steps 8 to 13.
With most Genie units, remove the light lens globe to expose the Learn Button on the motor head. The learn button is sometimes located on the back of the unit, or with Accelerator openers, it is under the light lens near the hinge of the lens globe. Always locate the floppy antenna wire first. The Learn Button can be found not far from this antenna. See Troubleshooting Guides for Accelerator photo.
Model 2: Intellicode Model GWKP (off-white with flip-up cover) Programming Instructions for the GWKP Genie garage door opener keyless entry involves following the two sets of steps below:. To erase the old PIN (personal identification number) press and hold down, in order, the “PROG,” “6” and “Up/Down Arrow” keys. The red LED will blink once and then turn off. Release the buttons.
To program: press, in order, but do not hold down the “3,” “5,” “7” and “PROG” keys. Enter your chosen PIN, anywhere from 3 to 8 characters. Press “PROG” (red LED blinks – twice per second and turns off) Find the Learn Code Button and the LED indicator light on your Genie motor head inside the garage.
Craftsman Garage Door Opener Manual Pdf
It is usually behind the light lens and close to the floppy antenna wire. If your Door Opener does not have an antenna, you have an External Receiver.
The External Receiver cover must be removed to access the Learn Code button and the indicator LED. Follow Steps 1 through 3 outlined below:. Press this Learn Code button momentarily. The red LED indicator light will start to blink. It will blink for up to 30 seconds. While it is blinking, proceed to Step 2:. Enter your PIN and press the “Up/Down Arrow” key on your keypad.
The Learn Code Indicator LED will stay on. Press the “Up/Down Arrow” key again. The Learn Code indicator LED turns off.
Wait until the Keypad backlight turns off (approximately 30 seconds). Test by entering your PIN and pressing the “Up/Down Arrow” key to operate your door. Multiple Genie Garage Door Opener Programming for GWKP- All garage doors will use the same PIN:.
Enter PIN and press PROG (red LED blinks once per second). Press PROG again (red LED blinks twice per second). Press the number of doors you wish to control (2 key or 3 key). Press PROG (red led blinks several times and turns off). Decide which Door will be Door #1, #2, and #3. Press the Learn Code Button on the motor head. Enter your PIN and press the Up/Down key on the Keypad.
Press the number you have picked for this Door Opener (key 1, 2 or 3). Press the Up/Down key. Repeat steps 6 through 9 for each Door Opener. Homelink Garage Door Opener Programming HOMELINK IN-CAR REMOTE PROGRAMMING INSTRUCTIONS To program a built-in-car transmitter to a rolling code garage door opener (Genie rolling code is called Intellicode, Liftmaster/Sears is called Security plus), you should take the following steps. Clear out anything previously programmed into the in-car system from the factory by holding down on the 2-outside buttons simultaneously, until the in-car LED starts flashing rapidly.
This may take up to a minute (in most cases, the key should be on auxiliary, and/or the car door must be shut). Decide which button you want to make to be your in-car garage door transmitter. Hold your transmitter up near the selected button, pressing both the garage door remote and the selected in-car transmitter button simultaneously. Hold down on the buttons until the in-car, LED light flashes rapidly. This sets the in-car remote transmitter to be your garage door openers make transmitter, but you are not done. You now need to make this in-car transmitter your personal transmitter. Go to the Learn Button on your garage door opener.
The button is usually next to the area where the floppy antenna is connected to the motor head. With Genie it is most often behind the light lens, and an indicator light flashes red when pressed. With Sears or Liftmaster (Chamberlain) it is near, or part of, the terminal screw board, and is a red, green or purple square button with a green, amber or purple indicator light. Press this learn button momentarily. The indicator light will turn on and blink if Genie or otherwise stay lit. For Genie systems, go back to the in-car transmitter button you programmed and press this button 3 or 4 times, or until the door starts moving.
This should set your in-car transmitter to your garage door opener. For Liftmaster, Sears, or Linear Megacode press and hold the in-car button you programmed until the garage opener light flashes. Your in-car is now programmed to operate your door. Programming a Fixed-Code Device (Majority of units made prior to 1996) These devices have internal dip-switches located near the battery of your remote. Clear out anything previously programmed into the in-car system from the factory by holding down on the 2-outside buttons simultaneously, until the in-car LED starts flashing rapidly. This may take up to a minute. (In most cases, the key should be on auxilary, and/or the car door must be shut).
Press and hold the in-car button you want to use to operate your garage door while simultaneously pressing and holding the button to your hand held remote until the LED on the in-car remote flashes rapidly. Test the in-car remote by pressing the button you chose to operate your door.
When the door operates your in-car remote is programmed. UNIVERSAL HOME REMOTE FOR HOMELINK (UHR) Programming a Rolling Code Garage Door Opener If your in-car (UHR) remote has 3 LED lights, one above each button, you should follow the instructions below to program your Rolling Code Garage Door Opener.
Press the outer two in-car (UHR) buttons simultaneously and release (In most cases, the key should be on auxilary, and/or the car door must be shut). Place the garage door opener into “learn” mode by pressing the small square colored button, or the small round black button on a Genie, located behind the light bulb globe in the garage. This may require the use of a ladder, follow all safety precautions. The LED on the garage door opener will go on immediately. For Genie openers the LED will begin blinking. Press and hold the button on the in-car (UHR) remote that you want to use for operation of the garage door to activate. Watch for the garage door to activate.
When the garage door activates, release the button and depress again the selected button to lock in the program. Programming of Rolling Code garage door opener is now complete. Programming a Fixed Code Device (Majority of units made prior to 1996) Below is a picture of a typical 12-switch DIP switch layout located on your hand-held remote control under the battery cover (your remote may have 8-12 DIP switches). Note: Genie, Linear, Multi-Code and Stanley have only 2 position switches: up or down. Press all three in-car (UHR) buttons simultaneously and release (In most cases, the key should be on auxilary, and/or the car door must be shut). Enter your corresponding DIP switch settings into your in-car (UHR) by pressing and releasing the buttons corresponding to the settings you show on your hand held remote or on the receiver, located on the ceiling of your garage, based on the above chart. For example: if the first switch is “UP” or “+”or “ON,” press the left button.
If the 2nd switch is “Down” or “-” or “OFF,” press the Right button. When you are done entering all the DIP switch settings, press all three in-car (UHR) buttons simultaneously and release. Press and hold the button that you want to use for operation.
Watch for the garage door to activate. When the garage door activates release the button and depress again the selected button to lock in the program. Programming of the Fixed Code device is now complete.
Namun, Kaisar dari kerajaan Liang Selatan Xiao Feng Qing, yang sebenarnya setengah alien, menyelamatkan Qian Qian. Qian Qian sejak saat itu hidup dengan nama Nie Wu Shuang dan memasuki istana kerajaan Liang.
Sebuah cinta segitaga antara Wu Shuang dan saudaranya Xiao terjadi.
Sears International Online Shopping If you are planning to visit the United States, or have friends and family here, shop at Sears to get everything you want—including gifts for yourself or others. Shopping online in the U.S. At Sears could not be easier. You can pay for your order in a store or even use an international credit card. Once you place an order, you (or someone you know) can pick it up at a Sears store, have it shipped to over 100 countries—whatever is most convenient for you. If you are looking to do some international online shopping, be sure to visit.
. Se deben realizar revisiones Periodic checks of the opener are periodicas del abridor de puertas required to ensure safe operation. Para asegurar su operacion segura. 00us Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A www.sears.com/craftsman. TABLE OF CONTENTS Introduction 2- 7 Adjustment 27-29 Safety symbol and signal word review.2 Adjust the travel limits.Preparing your garage door.
Adjust the force.Tools needed.Test the safety reversal system.Planning. Preparing your garage door Before you begin: To prevent possible SERIOUSINJURY or DEATH:. Disable locks. ALWAYS call a trained door systems technician if garage. Remove any ropes connected to garage door. Door binds, sticks, or is out of balance. An unbalanced.
Planning Do you have an access door in addition to the garage Identify the type and height of your garage door. Survey your garage area to see if any of the conditions below door?
If not, Model 53702 Emergency Key Release is required. Planning (Continued) ONE-PIECE DOOR INSTALLATIONS Without a properly working safety reversal system, persons (particularly small children) could be SERIOUSLYINJURED.
Generally, a one-piece door does not require or KILLED by a closing garage door. Reinforcement If your door is lightweight, refer to the. Carton Inventory Your garage door opener is packaged in one carton material. Parts may be stuck in the foam.
Hardware for which contains the motor unit and all parts illustrated assembly and installation is shown on the next page. Accessories will depend on the model purchased. Save the carton and packing material until installation If anything is missing, carefully check the packing and adjustment is complete. Hardware Inventory Separate all hardware and group as shown below for the assembly and installation procedures. ASSEMBLY HARDWARE Bolt 1/41'-20x 1-3/4 ( 1 ) )))iilill) Master 3/8' (1) Bolt 1/4'-20x2-1/2 Link (2) Idler Bolt (1) Trolley Threaded Shaft (1) Lock Washer Spacer (2) Washer. ASSEMBLY STEP Assemble the Rail & Install the Trolley To prevent INJURYfrom pinching, keep hands and fingers away from the joints while assembling the rail. To avoid installation difficulties, do not run the garage door opener until instructed to do so.
The front rail has a cut out 'window'. ASSEMBLY STEP Fasten the Rail to the Motor Unit To avoid SERIOUSdamage to garage door opener, use ONLY those b01ts/fasteners mounted in the top of the opener. Insert a 1/4'-20x2-1/2 bolt, washer and spacer into the cover protection bolt hole on the back end of the rail as shown. ASSEMBLY STEP Install the Chain/Cable To avoid possible SERIOUSINJURYto fingers from moving garage door opener: 1. Pull the cable around the idler pulley and toward the. ALWAYSkeep hand clear of sprocket while operating trolley.
Connect the cable to the retaining slot on the trolley, as. ASSEMBLY STEP Tighten Chain Figure 1 Trolley Outer Lock Threaded.
Spin the inner nut and lock washer down the trolley Washer Shaft threaded shaft, away from the trolley. To Tighten Outer Nut. To tighten the chain, turn outer nut in the direction shown (Figure 1).
INSTALLATION STEP Un.f!nished Determine Header Bracket Location Ceiling BRACKETHEADERFoRMOUNTCEIL HeaderWall Vertical Centerline of Garage Door To prevent possible SERIOUSINJURYor DEATH:. Header bracket MUST be RIGIDLYfastened to structural Structural Supports support on header wall or ceiling, otherwise garage door might NOT reversewhen required. INSTALLATION STEP Wall Mount Install Header Bracket You can attach the header bracket either to the wall above the garage door, or to the ceiling. Follow the instructions which will work best for your particular requirements.
Do not install the header bracket over drywall. INSTALLATION STEP Attach Rail to the Header Bracket. Position the opener on the garage floor below the header bracket, Use packing material as a protective base, NOTE: If the door spring is in the way you'll need help. Have someone hold the opener securely on a temporary support to allow the rail to clear the spring. INSTALLATION STEP Position Opener To prevent damage to garage door, rest garage door opener rail on 2x4 placed on top section of door.
Follow instructions which apply to your door type as illustrated. SECTIONAL DOOR OR ONE-PIECE DOOR WITH TRACK A 2x4 laid flat is convenient for setting an ideal door-to-rail distance. INSTALLATION STEP Hang Opener To avoid possible SERIOUSINJURYfrom a falling garage door opener, fasten it SECURELY to structural supports of Three representative installations are shown. Yours may the garage. Concrete anchors MUST be used if installing any be different.
Hanging brackets should be angled brackets into masonry. iNSTALLATiON STEP Irestall Door Control To prevent possible SERIOUSINJURYor DEATHfrom electrocution: Locate door control within sight of door, at a minimum. Be sure power is NOTconnected BEFORE installingdoor height of 5 feet (1.5 m) where small children cannot control. Reach, away from moving parts of door and door.
INSTALLATION STEP Install the Lights To prevent possible OVERHEATING of the endpanel or light socket:. Press the release tabs on both sides of lens. Gently. DO NOT use short neck or specialty light bulbs.
Rotate lens back and downward until the lens hinge is. INSTALLATION STEP Electrical Requirements To prevent possible SERIOUSINJURYor DEATHfrom electrocution or fire: To avoid installation difficulties, do not run the. Be sure power is NOTconnected to the opener, and opener at this time.
Disconnect power to circuit BEFORE removing cover to To reduce the risk of electric shock, your garage door establish permanent wiring connection. INSTALLATION STEP Install The Protector System ® Be sure power is NOTconnected to the garage door opener BEFORE installing the safety reversing sensor.
The safety reversing sensor must be connected and To prevent SERIOUSINJURYor DEATHfrom a closing aligned correctly before the garage door opener will garage door: move in the down direction. INSTALLING THE BRACKETS Figure 1 DOOR TRACK MOUNT (RIGHT SIDE) Be sure power to the opener is disconnected. Install and align the brackets so the sensors will face each other Door across the garage door, with the beam no higher than 6' Track (15 cm) above the floor. MOUNTING AND WIRING THE SAFETY REVERSING Figure 5 SENSORS Wing Nut. Slide a 1/4'-20xl/2' carriage bolt head into the slot on each sensor. Use wing nuts to fasten sensors to brackets, with lenses pointing toward each other across the door.
Be sure the lens is not obstructed by CarriageBolt - a bracket extension (Figure 5). INSTALLATION STEP Fasten the Door Bracket Fiberglass, aluminum or lightweight steel garage doors WILL REQUIREreinforcement BEFORE installation of door bracket. Follow instructions which apply to your door type Contact your door manufacturer for reinforcement kit. As illustrated below or on the following page. A horizontal reinforcement brace should.
ONE-PIECE D OORS Please read and comply with the warnings and reinforcement instructions on the previous page. They apply to one-piece doors also. Center the door bracket on the top of the door, in line with the header bracket as shown. Mark either the left and right, or the top and bottom holes.
INSTALLATION STEP Figure 1 Pulley Connect Door to Trolley IL. 8' (20 cm)min, Follow instructions which apply to your door type as amlmllmo illustrated below and on the following page.
Trolley / /O -'/'t Outer stopBo,t /,nne,! SECTIONAL DOORS ONLY Trolley Ring. ALL ONE-PIECE DOORS Figure 5 CORRECT INCORRECT 1.Assemble the door arm, Figure 5: IMPORTANT: The groove on the straight door arm MUST face away from the curved door arm. Fasten the straight and curved door arm sections together to the longest possible length (with a 2 or 3 Door Arm (Groove hole overlap). ADJUSTMENT STEP Adjust UP and DOWN Travel Limits Without a properly installed safety reversal system, persons (particularly small children) could be SERIOUSLYINJURED Limit adjustment settings regulate the points at which the or KILLED by a closing garage door. Door will stop when moving up or down. ADJUSTMENT STEP Adjust Force Without a properly installed safety reversal system, persons (particularly small children) could be SERIOUSLYINJURED Force adjustment controls are located on the right panel or KILLED by a closing garage door.
Of the motor unit. Force adjustment settings regulate the. ADJUSTMENT STEP Test Safety Reversal System Without a properly installed safety reversal system, persons (particularly small children) could be SERIOUSLYINJURED TEST or KILLED by a closing garage door.
Safety reversal system MUST be tested every month. With the door fully open, place a 1-1/2' (3.8 cm) board (or a 2x4 laid flat) on the floor, centered under the. OPERATION IMPORTANT SAFETY INSTRUCTIONS To reduce the risk of SEVERE INJURY or DEATH: 1. READAND FOLLOWALL WARNINGSAND INSTRUCTIONS. If one control (force or travel limits) is adjusted, the other control may also need adjustment. ALWAYSkeep remote controls out of reach of children. NEVERpermit children to operate or play with garage door 10.
Using Wall-Mounted To Open the Door Manually Door Control THE PREMIUM CONTROL CONSOLE 'igh4edutt°n To prevent possible SERIOUSINJURYor DEATHfrom a Press the lighted push button to open falling garage door: or close the door. Press again to. If possible, use emergency release handle to disengage reverse the door during the closing trolley ONLYwhen garage door is CLOSED.Weak or cycle or to stop the door while it's.
CARE OF YOUR OPENER THEREMOTE CONTROL B ATTERY LIMIT AND FORCE ADJUSTMENTS: Weather conditions may cause To prevent possible SERIOUSINJURYor DEATH: FORCE CONTROLS some minor changes in door. NEVERallow small children near batteries. Operation requiring some.
If battery is swallowed, immediately notify doctor. Re-adjustments, particularly To reduce risk of fire, explosion or chemical burn: during the first year of operation. HAVING A PROBLEM? My door will not close and the light bulbs blink on my motor unit: The safety reversing sensor must be Bell Wire connected and aligned correctly before the garage door opener will move in the down direction. Bell Wire Your garage door opener is programmed with self-diagnostic capabilities. The 'Learn' button/diagnostic will flash a number of times then pause signifying # has found Safety Reversing Sensor a potential issue.
Consult Diagnostic Chart below. Diagnostic Chart.' . Symptom: One or both of the Indicator lights on the safety sensors do not glow steady. PROGRAMMING NOTICE: If this Security garage door opener is operated with a non-rolling code transmitter, the technical measure in the receiver of the garage door opener, which provides security against code-theft devices, will be circumvented. The owner of the copyright in the garage door opener does not authorize the purchaser or supplier of the non-rolling code transmitter to circumvent that technical measure. To Add, Reprogram or Change a Keyless Entry NOTE: Your new Keyless Entry must be programmed to operate your garage door opener.
USING THE 'LEARN' BUTTON USING THE PREMIUM CONTROL CONSOLE NOTE: This method requires two people if the Keyless 1. REPAIR PARTS 144C56 Idler pulley 41A5807 Chain and cable 12D598-1 'U' bracket NOT SHOWN 183A163 Wear pads Installation Parts PART DESCRIPTION 41 A4884 Premium control console 41A6140-1 3-Function remote control case (no circuit board) 10A20 3V2032 Lithium battery 29B137 Visor clip 31 D543-1 Keytess entry keypad cover 41C541. Motor Unit Assembly Parts (Down) LIMIT SWITCH Brown Contact ASSEMBLY Wire ,. Wire.'
Drive.,.Gear X; // /// Center Limit (Up) Yellow Contact Contact Wire PART PART DESCRIPTION DESCRIPTION 41A5615 Chain Spreader 41A5525-37 Cover 41 C4220A Gear and sprocket assembly. You pay for labor, WARRANTY RESTRICTION This Craftsman Garage Door Opener Limited Warranty does not cover light bulbs or repair parts necessary because of operator abuse or negligence, including the failure to install, adjust and operate this garage door opener according to instructions. CONTENIDO Introduccibn Ajustes 27.29 Revisi6n de los simbolos y terminos de seguridad.2 Ajuste el limite del recorrido. Preparaci6n de la puerta de su cochera.Ajuste la fuerza. Herramientas necesarias.Pruebe el sistema de retroceso de seguridad. Preparaci6n de la puerta su cochera Para evitar una LESIONGRAVEo INOLUSOLA MUERTE: Antes de comenzar:.
SIEMPRE Ilame a un tcnico profesional para que le d. Quite los seguros. Servicio a su puerta de cochera si sta se atora, se pandea o est. Planificaci6n Observe el punto donde la puerta hace contacto con el piso. El espacio entre la base de la puerta y el piso no debe exceder 6 mm (1/4 de pulgada). Si no es asi, se corre el riesgo de que el Identifique la altura y el tipo de su puerta de cochera.
Planificaci6n (continba) INSTALACION CON PUERTAS DE UNA SOLA PIEZA Sin un sistema de retroceso de seguridad que funcione debidamente, al cerrar la puerta de la cochera se corre el riesgo. Generalmente una puerta de una sota pieza no requiere de que las personas (y en particular los niSos pequeSos)sufran refuerzos adicionates. Inventario de la Caja de Cart6n Su abridor viene empacado en una caja de cart6n que contiene en el mismo.
Toda la tornilleria y las piezas necesarias para el el motor y las piezas que se muestran en la siguiente ilustraci6n. Montaje e instalaci6n de su puerta se ilustran en la siguiente Tome nota de que los accesorios dependeran del modelo que pagina. Inventario de Piezas Antes de ta instataci6n, organice todas las piezas en grupos como se muestra en la siguiente ilustraci6n. TORNILLERiA Y PIEZAS PARA EL MONTAJE Perno de 1/4-20xl-3/4 pulg. (1).Enlace maestro (2) Tuerca de Perno de 1/4-20x2-1/2 de pulg.
(1) 3/8 pulg. MONTAJE, PASO Monte el Riel e instale el Trole Para evitar QUESE PELLIZQUE,conserve los manos y dedos lejos de las juntas cuando monte el reil. No encienda ni use el abridor hasta que Ilegue al paso de la instalacion correspondiente, de otra manera corre el riesgo de complicar el proceso de instalacion. MONTAJE, PASO Fije el Riel a la Unidad del Motor Use SOLOel perno y la tuerca que vienen montados en la parte superior del abridor para evitar que el abridor de la puerta de. Introduzca un tornillo de 1/4-20 x 2-1/2 de pulg., con arandela cochera se dae SERIAMENTE.
MONTAJE, PASO Instale la Cadena y Cable Para evitar posibles LESIONESGRAVESen los dedos causadas per las partes m6viles del abridor de puerta de cochera: 1. Jale el cable alrededor de la polea Ioca y hacia el trole.
SIEMPRE mantenga las manes lejos de la rueda dentada 2. MONTAJE, PASO Apriete la Cadena Figura 1.
Gire la tuerca interna y ajuste la arandela; baje ambas por et Tuerca Eje roscado eje roscado det trole, atej&ndolas del trole Para apretar externa Arandela deltrole. Para apretar la cadena, gire la tuerca externa en la direcci6n que se indica (Figura 1). INSTALACION, PASO Cielo raso INSTALACION sin acabado Determine d6nde instalar OPCIONALDE LA VlENSULA DEL la Mnsula Cabezal CABEZALEN EL CIELO RASO Pared Linea delantera Para evitar unaposible LESIONGRAVEo INOLUSOLA MUERTE: vertical de la. La mnsula del cabezalDEBEquedar RJGIDAMENTE sujeta al raje 5x10 cm (2x4 pulg.) soporte estructural en la pared delantera o en el cielo raso, de.
Montaje en la pared INSTALACION, PASO Instale la Mnsula Cabezal La mnsula del cabezal se puede fijar a la pared justo por encima de la puerta de la cochera o en el cielo raso. Siga las instrucciones que sean mas adecuadas para su cochera. No instale la mnsula del cabezal en un muro falso.
INSTALACION, PASO Coloque el Riel en la Mnsula Cabezal Coloque el abridor sobre et piso de la cochera debajo de la mensuta del cabezal. Use el material de empaque como base para protegerlo.
NOTA: Si el resorte de la puerta est9 obstruyendo, va a necesitar ayuda. INSTALACION, PASO Coloque el Abridor en Posici6n Para evitar que la puerta de cochera sufra daffos, apoye el riel del abridor de la misma sobre un pedazo de madera de 5x10 cm (2x4 Siga las instrucciones correspondientes al tipo de puerta de su pulg.) colocado en la secci6n superior de la puerta. INSTALACION, PASO Cuelgue el Abridor Para evitar la posibilidad de una LESIONGRAVE si se cae el abridor de la puerta de cochera, sujtelo FIRMEMENTEa los Aquf se muestran tres ejemplos distintos para la instalaci6n; sin soportes estructurales de la cochera. Se DEBENusar sujetadores embargo, es posible que su cochera no concuerde con ninguno para concreto si alguna de las mnsulas se va a instalar en de ellos. NSTALAC ON, PASO Irestale Unidad Control Para evitar la posibilidad de una LESIONGRAVEo INCLUSOLA MUERTEpor electrocuci6n: Puerta.
ANTES de instalarel control de la puerta, cerci6rese de que la energia el(ctricaNO est conectada. Ubique el control de la puerta de manera que quede a la. INSTALACION, PASO Instale las Luces Para evitar un posible SOBRECALENTAMIENTO del portabombillas:. Oprima las lengQetas de liberaci6n a ambos lados de la lente.
NO utilice bombillas de cuello corto ni de tipo especial. Rote la lente suavemente hacia atras y hacia abajo hasta que. INSTALACION, PASO Requisitos para la Instalaci6n Para evitar la posibilidad de una LESIONGRAVEo INCLUSOLA Elctrica MUERTEpor electrocucidn o incendio:. Cercidrese de que el abridor NO est conectado a la energia Para evitar dificultades con la instalacibn, el@trica, y desconecte la alimentacidn el@trica al circuito ANTES encienda ni use el abridor en este momento. INSTALACION, PASO Instale La Sistema de Protecci6n ® Cerci6rese de que la energia elctrica NO est conectada al abridor de la puerta de la cocheraANTES de instalar el sensor del sistema El sensor del sistema de retroceso de seguridad debe estar de retroceso de seguridad.
INSTALACION DE LAS MINSULAS Figura INSTALAClON EN ELCARRIL DE LA PUERTA (LADO DERECHO) Asegdrese de que el abridor no estd conectado a la corriente eldctrica. Carril de Instale y alinee las mnsulas de manera que los sensores estn uno frente al otro en los lados opuestos de la puerta, a una Reborde distancia maxima de 15 cm (6 pulg.) del piso. MONTAJE Y CABLEADO DE LOS SENSORES Figura Tuercade mariposa SISTEMA DE SEGURIDAD DE REVERSA. Deslice la cabeza de un perno de coche de 1/4-20xl/2 pulgada dentro de la ranura de los sensores. Use tuercas de mariposa para sujetar los sensores alas mnsulas, con las Pernode coche ' lentes de cada sensor frente a frente a ambos lados de la. INSTALACION, PASO Fije la Mnsula de la Puerta En puertas de garaje de fibra de vidrio, aluminio o acero liviano ES NECESARI0colocar los refuerzosANTESde instalar la m6nsula Siga las instrucciones que correspondan at tipo de puerta que de la puerta. Consulte con elfabricante de la puerta sobre juegos usted tenga, segQn las ilustraciones siguientes o de la pr6xima prefabricados de refuerzo.
PUERTAS DE UNA SOLA PIEZA Lea y respete todas las advertencias e instrucciones respecto a los refuerzos contenidas en la p&gina anterior, ya que son v&tidas tambien para puertas de una sota pieza. Centre la mensuta en ta parte superior de ta puerta, alineada con ta mensuta det cabezat, tal se muestra en la itustraci6n. Figura 1 INSTALACION, PASO Conecte el Brazo de la Puerta al Trole Siga las instrucciones que correspondan al tipo de puerta de cochera que usted tenga, como se muestra a continuacion yen Trole la pa.gina siguiente.
Exterior SOLO PARA PUERTAS SECCIONALES Pasadorde chaveta de 5/16xl pulg. TODAS LAS PUERTAS DE UNA SOLA PIEZA Figura 5 CORRECTO INCORRECTO 1. Arme el brazo de la puerta, Figura 5: IMPORTANTE: El ranura en el brazo recto de la puerta DEBE volteese de/brazo curvado de la puerta. Sujete las dos secciones de los brazos de la puerta (recto y curvo) a la mayor distancia posibte, de manera que dos o tres de los orificios se sobrepongan uno at otro. AJUSTES, PASO Ajuste el Limite del Recorrido Si el sistema de retroceso de seguridad no se ha instalado HACIA ARRIBA y HACIA ABAJO debidamente, las personas (y los niSos pequeSos en particular) podrian sufrir LESIONESGRAVESo INCLUSOLA MUERTEcuando At ajustar el limite det recorrido de la puerta, se reguta hasta se cierra la puerta de la cochera.
AJUSTES, PASO Ajuste la Fuerza Si el sistema de retroceso de seguridad no se ha instalado debidamente, las personas (y los nios pequeos en particular) Los controles para el ajuste de la fuerza det abridor se podrian sufrir LESIONESGRAVESo INCLUSOLA MUERTEcuando encuentran en et panel de posterior de la unidad del motor. AJUSTES, PASO Pruebe el Sistema de Retroceso Si el sistema de retroceso de seguridad no se ha instalado Seguridad debidamente, las personas (y los nifios pequefios en particular) podrian sufrir LESIONESGRAVESo INCLUS0 PRUEBA LA MUERTEcuando se cierra la puerta de la cochera. OPERACION IMPORTANTES DE SEGURIDAD INSTRUCCIONES Para reducir el riesgo de LESIONES GRAVES o la MUERTE: 1.
LEA Y RESPETE TODASLAS ADVERTENCIASE INSTRUCCIONES. Cuando se ajusta uno de los controles (limites de fuerza o de recorrido), es posible que sea necesarioajustar tambin el otro 2. C6mo Usar la Unidad de Control C6mo Abrir la Puerta Manualmente de Pared LA CONSOLA DE CONTROL PREMIUM I -'-', Bot6n Iluminado Para evitar la posibilidad de una LESIONGRAVE o INOLUSOLA Oprima el bot6n iluminado para abrir o MUERTE si la puerta de la cochera se cae: - Bot6n cerrar la puerta.
LA BATER A DEL CONTROL REMOTO MANTENIMIENTO DE SU ABRIDOR DE PUERTA COCHERA Para evitar la posibilidad de LESIONESGRAVES0 incluso LA MUERTE: AJUSTES DE LJMITE Y FUERZA:. NUNCApermita que los niSos pequeSos estn cerca de las Las condiciones climatol6gicas CONTROLES DE FUERZA baterias. SI TIENE ALGON PROBLEMA 1. La puerta no cierra y las luces de la unidad del motor parpadean: El sensor del sistema de retroceso de seguridad Cable de carnpana debe estar instalado y alineado correctamente para que el sistema de apertura de la puerta de la cochera se mueva en sentido descendente. Cablede El sistema de apertura de la puerta cuenta con una funci6n de autodiagn6stico.
El bot6n 'Aprender'/LED de diagn6stico parpadeara Sensor de seguridadde reversa varias veces antes de detenerse, indicando que ha encontrado un posible problema. Consulte la tabla de diagndstico a continuacidn. Tabla de Diagn6stico. COMO PROGRAMAR EL ABRIDOR AVISO: Si utiliza este abre puertas de garaje Security,J con un transmisor no dotado de un sistema de cddigos de salto (cddigo aleatorio), se veran circunvenidas las medidas tecnicas incorporadas en el receptor del abridor para proteger contra los aparatos de captura de cddigos. Cbmo Agregar, Reprogramar o Cambiar un Cbdigo de Entrada sin Llave NOTA: Su nueva Entrada sin Ilave debe programarse para que opere el abridor de la puerta de su cochera. COMO USAR EL BOTON LEARN (APRENDER) COMO USAR LA CONSOLA DE CONTROL PREMIUM 1.
Usted paga per el trabajo. Restriccion de la garantia Este garantfa limitada del abridor de puerta de cochera de Craftsman no cubre las bombillas ni la reparaci6n despiden necesario a causa del abuso de operario ni. Your Home For troubleshooting, product manuals and expert advice: managemylife www.managemylife.com For repair - in your home - of all major brand appliances, lawn and garden equipment, or heating and cooling systems, no matter who made it, no matter who sold it! For the replacement parts, accessories owner's manuals that you need to do-it-yourself.
The nucleus of any garage door system is its opener. Easily overlooked, garage door openers are highly complex pieces of equipment, often containing dozens of intricate parts that work simultaneously with one another to consistently raise and lower your door. You'll know that you're getting the best from Sears as it's the home to America's #1 Garage Door Opener Brand, Craftsman. Below you will find the top 4 items to consider when looking at purchasing a new garage door opener. Power Ratings Sears' Craftsman garage door openers have power ratings to accommodate any home's needs.
From ½ to 1 ¼ horsepower, our experts can work directly with you to determine the most appropriate opener for your garage door. Drive Mechanism Sears offers two different drive mechanisms to accommodate your home and budget. If you're looking for a smooth and quiet opener for a garage door with rooms located above the garage or attached to the garage, the belt drive is going to be the best for you.
You can also choose a chain drive opener, which is perfect for garages that are unattached to the home. Reliability Sears offers some of the strongest warranty packages in the industry. Up to a lifetime on the door sections on all the Sears Carriage House Collection and Sears' three-layer Traditional Steel Collection garage doors. Sears warranties on labor and hardware is as good as, or better than, other garage door brands. Battery Backup is also included with select garage door openers.
This feature allows your garage door opener to work without power for up to 20 cycles to ensure you will be able to access the garage during a power outage. This is a critical component to many homeowners who rely on the garage as the main entry point to the home. Connectivity If you want to connect your new garage door to your smartphone, then you're in luck! The Craftsman AssureLink™/SmartControl Internet Gateway allows you to monitor and operate your garage door from anywhere with your internet-enabled smartphone, cell phone, laptop, or tablet via the Craftsman AssureLink™ mobile app or web-interface. It's Perfect for those times when you are away from home and can't remember if you have closed your garage door or provide access to your home (via garage door) as needed for family, friends, deliveries, etc.
When you aren't at home With multiple options and the ability to consult with a trained garage door opener expert we are certain we have the right opener to meet your needs. Please take a few moments to review the options below and explore the features, and functions each opener provides.Per Stevenson Traqline. Unit market share for 12 months ending June 30, 2015.